You will see a flashing frame marquee around the selected area. Cleaning the Glass Surface on the Digitizer 1. It can help to improve the dynamic range for final scanned images. Our more advanced gauges offer some unique features and have unparalleled precision whilst staying cost effective. Our entry level 100 Series are simple to use gauges with a range of dual element probes for standard thickness measurements or simple corrosion mapping. Then, remove the digitizer from the wrapped plastic bag.
However, the maximum limit for the width of the Light Shield is about 10. Refer to the ScanWizard Industry software manual for more details. Usuarios navegando por este Foro: No hay usuarios registrados visitando el Foro y 0 invitados No podés abrir nuevos temas en este Foro No podés responder a temas en este Foro No podés editar tus mensajes en este Foro No podés borrar tus mensajes en este Foro No podés enviar adjuntos en este Foro Buscar: Saltar a:. Ensure that you put your shipping carton toward the right direction. Pulse mode is set for instruments duty cycle. Incorporated Into All Models Auto-set is the most outstanding feature ever designed into an.
Pull up the Light Shield before pulling out the glass Note: Before pulling out the glass, make sure that the Light Shield has been pull up. Rather than offer many dedicated to various applications, the transducer actually sets a single gage to optimize for a given application. Remove two accessory boxes 1 and 2 from the foam supports. Conversely, material velocity can be measured for material of known thickness. A proprietary monolithic integrated circuit chip and a highly advanced micro-computerized design have permitted the achievement of performance levels considered only conceptual, The outgrowth of this technology has been the development of three portable and two Bench top models in the Nova 900 Series. Instant and repeatable measurements can be made in a non-destructive way with access needed from only one side of the material.
Not responsible for typographic errors. However, Microtek makes no guarantee as to the accuracy of the contents of this document and reserves the right to make changes to the contents without prior warning. With a ruggedized aluminum construction yet small and ergonomic size, the thickness gauges are renowned for ease of use and longevity in the field. Operation is subject to the following two conditions: 1 This device may not cause harmful interference, and 2 this device must accept any interference received, including interference that may cause undesired operation. The Nova 900 series are precision gauges offering higher accuracy than the general purpose gauges.
Or, Insert and push down both sides of the Output Basket into its compartment holes, making sure the Output Basket snaps into place. Reduces average input line power by 70%, reducing energy costs and heat build up. . Some standard features include High Speed Pulse Rep Rate, 0. To clean the two sets of rollers: 1.
Release Buttons Releases the front cover to open the lamp holder. Lift up the upper foam support. Pull out the digitizer from the bottom foam support. Please don't select fast preview or draft scan! In addition, carrying out a regular inspection at least once a year. Its user-friendly interface enables you to easily start the scanning process and finish all the scan jobs. Close the top cover of the shipping carton and seal it with tape. Use it to pull out the glass, shown as in the graph below.
When an A-trace or encoded B-scan is required, the high-precision is the dual element probe solution and more advanced will support single or dual element probes. This section shows you how to position a single-sheet of X-ray film into the Feed Tray. These ruggedized, highly stable models have been carefully designed to offer a choice of features to best suit the application level, gauging environment and user preference. It automatically recognizes the transducer which has been selected for a given application and then automatically sets all corresponding circuit parameters for peak performance. A battery low charge level indicator is included, while a power cut-off circuit automatically protects the battery pack from unintentional over or discharge. The Nova 910 thickness tester is a basic gauge emphasizing operational simplicity for the more straightforward, less demanding applications.
There are two Release buttons located on each side of the front cover. This section shows you how to position a single-sheet of X-ray film into the Feed Tray with the aim of the Light Shield. Auto-set's elaborate software program issues digital commands to optimize and properly set the pulser characteristics, transducer damping and zero auto-zero , receiver characteristics, a host of logic and gating functions, the thickness readout range auto-range and gaging precision. Insert and push down both sides of the Feed Tray into its compartment holes, making sure the Feed Tray snaps into place. The auto probe recognition recognizes the transducer and automatically sets all corresponding instrument parameters for peak performance for most inspection requirements. Available in hand held or Bench top configuration, a range of transducers are available to cover most precision thickness gauging requirements.
Make sure that the Light Shield has been pull up. Due to the heavy weight of the package about 33 pounds , make sure you can handle it properly before removing it from the carton. All five models provide the identical base gauging performance, with variations in options and the supporting features. The product may slide or fall, causing serious injury to people as well as serious damage to the product. After cleaning the glass and the components, along the tracks, push back the glass surface until it snaps into place. Find a perforation at the left of the glass.
Velocity control Calibration is performed by either entering the know ultrasonic velocity for the material being gaged or by setting up on a known thickness of the material. Provides very active movement of wet and dry particles for enhanced flaw definition, especially when using the coil method, which adds a physical vibration into the part. With both hands, hold the two sides of foam supports firmly and then insert them into the shipping carton. Special instruments include the , customized for cylinder bore wall thickness measurements in automotive engines. Also to conserve battery charge level, the gage automatically turns itself off if not used after a short time.